How to Go About boarding up services Up a Door

Boarding up a door is one method to shield vacant investment properties from the elements. It's not guaranteed to stop every damage, but it can help to prevent certain problems that come with severe storms.

The commercial boarding up service of doors and windows can also deter burglars and vandals. However it can be costly and time-consuming to put plywood boards over the openings on a house.

Take a measurement of the door

The first thing you'll need is tape measure. You might also want to keep an extra chair or ladder in case you need to see more clearly at the top of the frame. Wear gloves and goggles if you have to use these tools.

Once you have the measuring instrument, start by taking the door width measurement. This can be done by running the tape measure horizontally across the door. Be sure to remove all additional parts of the door, for instance a sweep, when measuring. Then, take a measurement of the height from the floor up to the existing sill or lintel. It is important to measure more than one location particularly with older doors, because they may not be an exact rectangle. If the measurements are different, use the largest figure.

After you've taken the width and height measurements then you'll have to determine the size of board you'll need for the frame. Ideally it should be 2'' wider than the door and 1 inch thicker than the door. 2'' higher. This will give enough space to shim both the frame and frame in place.

When you're ready to take the door frame's width and height measurements It's recommended to remove any trim or casing around the door jambs so you can see the studs that are behind them. This will allow you to determine the exact dimensions of the gap between studs and the edge of the frame.

After removing the trim, measure the width of the door frame using a tape measure. Measure the frame at three different places and then use the smallest measurement. Also, you should determine the height of the frame from top to bottom on both sides, and then use the shortest measurement as the height of your door.

If you're having issues with the measurements, seek out a professional who will come to your home and do the measurements. They will tell you what size and style of door you require and how to prepare your frame for a new door.

Plywood can be cut into pieces

A door frame is typically comprised of a set of thin boards or studs that create a hollow space around the door. A typical door is held in place by two hinges that are fixed to the studs. If you are looking to finish the door, you'll need to remove it from its hinges over night. To prevent insects from entering your home and to secure the door's opening, a quick and easy method to board doors is to place plywood in the opening. This is easy to do without the need to nail or screw the plywood to the frame of the door.

Plywood is simple to work with, affordable and looks great once it's finished. It is the ideal material to use as a temporary solution for situations where you have to take down the door you have in place to finish it or build the new one. It is also a great option for securing the opening in a room that is being renovated, such as an unfinished basement, or a construction site.

To install a plywood wall begin by taking measurements of the width and height of the door opening. Note the measurements using a utility blade and a straight edge made of metal, such as the drywall or metal square. Next, snap a chalk line across the lines marked to indicate where you'll need to cut. Then utilize circular saws to cut out the plywood into a size.

It is important to protect your ears and eyes while cutting plywood. If possible, wear a pair of eye protection and earplugs as you are working. It is also essential to use a blade with many teeth, which will allow you to cut quickly and without any tear-out. Utilize a small piece of wood to guide the blade. Keep it a hair's width away from the marked line when cutting.

An effective way to hold the plywood in place without screwing it to the studs is by fixing braces that are short at each end. Place one of the braces on the inside of the door and boarding up a door the other on the outside. Install a deck screw in each hole and tighten by using an open-end ratchet.

Fix the Plywood

It's time to attach the panel to the frame once you have the plywood sheet cut to the proper dimensions and the holes for the rails and stiles of the door frame predrilled. This is a simple project that doesn't require advanced carpentry skills if you use the correct tools and follow the right procedures.

Set boarding up doors a table in the entrance with two sawhorses at each end and framing lumber 2x4s. Lay the entire sheet of plywood flat on top the sawhorses and use the marks made during the measurement process as a guide to cut. Utilize a utility knife and a metal straight edge to score the lines. This will create a guideline for the saw blade, and will help keep the wood from splintering when cutting the plywood.

Wear eye protection and use a circular table saw equipped with a fine-toothed blade cut along the score line. Then sand the edges of the plywood panel using 120-grit sandpaper to smooth the panels and remove any burrs that may have formed from the saw cuts. After sanding process, apply a coat of wood sealer to the plywood panels, and let dry according to the instructions of the manufacturer.

Install the hinges on the door frame. If you're using a hinge with a T-hinge drill holes in the outer edge of your door to allow for the straps portion of the hinges. Then, put the outside hinge on its mark and attach it to the frame with a screw gun. Repeat the same procedure on the inside of the door for all of the remaining hinges, being careful not to overtighten any of them or the hinge could shift.

If you're using a single outside T-hinged door, you can make it easier to close and lock with a chain lock by putting a piece wire through the loops on the outside hinges. Fold a small piece of tie wire in half, and then put it through the two holes on the exterior of the door. Then twist the wires to secure the door.

Install the Plywood

Place the plywood into the door's opening according to the measurements you have taken. Shim the header of the frame (top) and the sill. Use a level to make sure there's no slop in either the header or sill. If it isn't perfect then place another shim if it is needed and continue the process until the sill and the header are plumb.

After the plywood is in place, secure it with the stainless-steel hinge bolts and wingnuts. Make use of a screwgun that has a hex head attachment to avoid removing the heads of the screws.

If you live in a house with studs running the length of your doorway, you can drill hanger bolts into every framing piece. This is a lot easier than using a drywall saw to create the hole.

After you have installed the plywood, measure the width and the height of the door opening. If necessary, trim your plywood bottom to fit the height of the door frame. Cut two pieces of framing lumber 1-by-6 as braces for the upper and lower edges. Cut along the lines marked on the plywood with circular blades with teeth that are finely tipped. Wear eye protection. Take any splinters out of the cuts with a Sanding block.

Once you have the braces in place, nail each one to the plywood with a pair of 2-inch finishing nails. Counter sink all nail heads when you're done. Cover the braces and plywood with a good wood sealer, like this wipe on polyurethane from Minwax.

If your door is too large, you can either add decorative molding to fill the space between your door and jamb or you can alter the size of your opening. However, in many situations, it's more affordable and easier to simply get the right door. This can also alleviate any problems that you might have faced with the original door, if it was damaged and no suitable for the opening.